Showing all 11 results

Show sidebar
Close

Mantotherm Acrylic Based Exterior Paint

Acrylic emulsion based, waterproof, long lasting, high quality, opaque finishing coat decorative exterior paint with silicon additive.

Mantotherm Silikonlu Dış Cephe Boyası is used as the finishing coat painting material along with the suitable primer on cement based plaster, exposed concrete, fiber cement board and thermal insulation systems of exteriors of buildings.

  • Reference Standardsa. Certifications / Standards
    TS 7847
    b. Ministry of Public Works and Settlement Item No.
    Ministry of Public Works and Settlement Item No.: 04.522/S
  • Application Surfaces
    Outdoors Walls;
    Cement based plasters (Mantotherm Astar applied)
    Concrete (MegaSıva K and MegaSıva İ applied)
    Fiber cement panels (Mantotherm Astar applied)
    Thermal insulation systems (as finishing coat paint)

    Surface Preparation :
    • Application surfaces should be sound, clean, dust free, and free from molding oils and other foreign substances. Such materials as mortar and cement residues should be peeled off.
    • Mantotherm Astar should be applied to such surfaces, which may have been painted previously or is to be newly painted.

    Application Methods :
    • Mantotherm Silikonlu Dış Cephe Boyası should be stirred until it becomes homogenously consistent prior to the application.
    • The product should be diluted with fresh water in such maximum volume that is equal to 10 – 15 % of the total volume, and be applied in 2 coats with a roller, brush or a spraygun.

    Application Recommendations :
    • In order to avoid any potential differences in shade on the façade, the product of the same batch number should be used on each facade.
    • Any extra water should not be added to the mixture.
    • The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing.
    • Due care should be given to prevent the exposure of the material to direct sunlight in hot weather conditions.
    • The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance.
    • The product should not be applied under windy or extremely hot weather conditions and under direct sunlight.
    • Refer to our technical support hotline for recommendation on different surface applications.

    Surface and Ambient Temperature
    The surface and ambient temperature should be between +5°C and +30°C whilst at application.

Close

Mantotherm Dekominera Grain Texture

White cement based, fiber reinforced surface finishing coat, which creates a natural texture on the surface.,

Mantotherm Dekominera – Tane Dokulu can be safely applied as the finishing coat on cement based fine plaster or thermal insulation systems in outdoors spaces. The product is also suitable for use on interior walls for decorative purposes.

Reference Standards

a. Certifications / Standards
TS 7847
ETA
b. Ministry of Public Works and Settlement Item No.
Ministry of Public Works and Settlement Item No.: 04.476/A

Application Surfaces
Indoors and Outdoors Walls;
Fine plastered surfaces
Thermal insulation systems

Surface Preparation :
• Mantotherm Dekominera – Tane Dokulu shall be applied minimum 12 hours after the application of Mantotherm Astar application on such floors, on which Mantotherm Sıva Harcı or MegaSıva Thermo prior to such primer application.

Application Methods :
• The homogenous mixture to be prepared should be applied to the surface smoothly and properly with a stainless steel trowel.
• Any surplus material should be peeled off the surface during the application in order to ensure a homogenous and smooth surface.
• Once the decorative coating is applied homogenously on the application surface, the pattern design should be performed within 10 minutes at maximum.
• Design patterns should be created with a plastic trowel on the surface by way of circular motion in order to create the graine texture. The surface of the trowel should be peeled off frequently during the pattern design.

Application Recommendations :
• The painting application should not be initiated before minimum 7 days following the mineral based lined texture decorative coating application.
• The product should, once mixed, be used before the expiration of its pot life. Any mortar, the pot life of which has expired, should not be used during the application.
• Any such foreign substance as lime, cement or plaster should not be added to the mortar prepared.
• Any extra water should not be added to the mixture.
• The surface should, subsequent to application, be protected from water and frost until it dries completely.
• The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing.
• Due care should be taken to ensure that the material is not exposed to direct sunlight in hot weather conditions, and the product should be mixed with cold water.
• The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance.
• The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours.
• Refer to our technical support hotline for recommendation on different surface applications.

Surface and Ambient Temperature
The surface and ambient temperature should be between +5°C and +30°C whilst at application.

Close

Mantotherm EPS Thermal Insulation Panel

Expanded polystyrene panel with high pressure resistance, used for the thermal insulation of walls, columns and girders.

    • Mantotherm EPS Isı Yalıtım Levhası is used as heat insulation material for the walls, terraces, floors and basements of buildings.

 

  • Application Surfaces
    Indoors Walls;
    Finishing coat applied surfaces
    Outdoors Walls;
    oughcast applied surfaces
    Surface Preparation :
    • The application surface should be dry, clean, sound and dust-free, and should have been cleansed of oil, dirt or any materials that may prevent adhesion, and any such materials as mortar and cement residues should be scraped from the application surface.
    • The old plaster coat, blistering and cracks on the facades should be scraped, be repaired with MegaTamir I or MegaTamir K, whereby a sound surface should be obtained.
    • In the case of bevels in excess of 2 cm on the surface; they should be repaired with MegaTamir I or MegaTamir K before insulation application.
    • The surface to be insulated should not be moist, and the flooring trowel coating and internal and external wall plasters should have dried.
    • There should not be any moisture in progress upward on the surface, the waterproofing should be completed as necessary and should have risen 30 cm above the ground soil.
    • The insulation application should be initiated minimum 4 weeks after the application of roughcast.
    • The rain gutters, cabling elements and the like on the façade should be placed over the system and be deployed in some 6 to 7 cm distance to the system.

    Application Methods :
    • Mantotherm EPS Isı Yalıtım Levhası, the reserve side of should have been applied Matotherm Yapıştırma Harcı adhesive mortar, should be firmly placed on the sub-basement profile.
    • In order for Mantotherm EPS Isı Yalıtım Levhası to thoroughly contact the wall and to ensure the smoothness of the surface, the panel should be slipped slightly and adhered to the wall, be gauged and linaged.
    • Mantotherm EPS Isı Yalıtım Levhası should be furnished in tusk tenon fashion. The tusk tenon should be continued also in the corner joint spots of the building.
    • Any unintentional gaps between any two Mantotherm EPS Isı Yalıtım Levhası should strictly be filled with pieces to be cut from the same material. Due care must be taken to ensure that the adhesive does not overflow at the edges, where panels join, any overflowing adhesive should be cleaned and the panel edges should be ensured to be clean.
    • The corners of the such gaps on the surface as window gaps and door gaps should be aligned with the panel joints, the Thermal Insulation Panels should be placed as a whole on the corners, screw threads should be cut and be sized for the gaps. Hence will be eliminated the risk of cracks on the corners.
    • Mechanical fixation on the surface of the Thermal Insulation Panels in addition to chemical adhesion is of utmost importance for long-lasting performance. Minimum 24 hours after the adhesion of the Thermal Insulation Panels, the dowelling should be performed with thermal insulation panel dowels Mantotherm Isı Yalıtım Levhası Dübelleri. Appropriate and suitable dowels should be selected with due consideration of the insulating material employed and the surface characteristics.

    Application Recommendations :
    • The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing.
    • Due care should be given to prevent the exposure of the material to direct sunlight in hot weather conditions.
    • The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance.
    • The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours.
    • Refer to our technical support hotline for recommendation on different surface applications. (PHONE: 444 4 595)

     

    Surface and Ambient Temperature
    The surface and ambient temperature should be between +5°C and +30°C whilst at application.

 

Reference Standards

a. Certifications / Standards
TS EN 13163
TS EN 13499
ETA

 

Close

Mantotherm Exterior Paint With Silicone

Acrylic emulsion based, waterproof, long lasting, high quality, opaque finishing coat decorative exterior paint with silicon additive.

Mantotherm Silikonlu Dış Cephe Boyası is used as the finishing coat painting material along with the suitable primer on cement based plaster, exposed concrete, fiber cement board and thermal insulation systems of exteriors of buildings.

Reference Standards

a. Certifications / Standards
TS 7847
b. Ministry of Public Works and Settlement Item No.
Ministry of Public Works and Settlement Item No.: 04.522/S

Application Surfaces
Outdoors Walls;
Cement based plasters (Mantotherm Astar applied)
Concrete (MegaSıva K and MegaSıva İ applied)
Fiber cement panels (Mantotherm Astar applied)
Thermal insulation systems (as finishing coat paint)

Surface Preparation :
• Application surfaces should be sound, clean, dust free, and free from molding oils and other foreign substances. Such materials as mortar and cement residues should be peeled off.
• Mantotherm Astar should be applied to such surfaces, which may have been painted previously or is to be newly painted.

Application Methods :
• Mantotherm Silikonlu Dış Cephe Boyası should be stirred until it becomes homogenously consistent prior to the application.
• The product should be diluted with fresh water in such maximum volume that is equal to 10 – 15 % of the total volume, and be applied in 2 coats with a roller, brush or a spraygun.

Application Recommendations :
• In order to avoid any potential differences in shade on the façade, the product of the same batch number should be used on each facade.
• Any extra water should not be added to the mixture.
• The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing.
• Due care should be given to prevent the exposure of the material to direct sunlight in hot weather conditions.
• The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance.
• The product should not be applied under windy or extremely hot weather conditions and under direct sunlight.
• Refer to our technical support hotline for recommendation on different surface applications. (PHONE: 444 4 595)

Surface and Ambient Temperature
The surface and ambient temperature should be between +5°C and +30°C whilst at application.

Close

Mantotherm Glass-Fiber Mesh

Acrylic emulsion based, waterproof, long lasting, high quality, opaque finishing coat decorative exterior paint with silicon additive.

Mantotherm Silikonlu Dış Cephe Boyası is used as the finishing coat painting material along with the suitable primer on cement based plaster, exposed concrete, fiber cement board and thermal insulation systems of exteriors of buildings.

Reference Standards

a. Certifications / Standards
TS 7847
b. Ministry of Public Works and Settlement Item No.
Ministry of Public Works and Settlement Item No.: 04.522/S

Application Surfaces
Outdoors Walls;
Cement based plasters (Mantotherm Astar applied)
Concrete (MegaSıva K and MegaSıva İ applied)
Fiber cement panels (Mantotherm Astar applied)
Thermal insulation systems (as finishing coat paint)

Surface Preparation :
• Application surfaces should be sound, clean, dust free, and free from molding oils and other foreign substances. Such materials as mortar and cement residues should be peeled off.
• Mantotherm Astar should be applied to such surfaces, which may have been painted previously or is to be newly painted.

Application Methods :
• Mantotherm Silikonlu Dış Cephe Boyası should be stirred until it becomes homogenously consistent prior to the application.
• The product should be diluted with fresh water in such maximum volume that is equal to 10 – 15 % of the total volume, and be applied in 2 coats with a roller, brush or a spraygun.

Application Recommendations :
• In order to avoid any potential differences in shade on the façade, the product of the same batch number should be used on each facade.
• Any extra water should not be added to the mixture.
• The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing.
• Due care should be given to prevent the exposure of the material to direct sunlight in hot weather conditions.
• The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance.
• The product should not be applied under windy or extremely hot weather conditions and under direct sunlight.
• Refer to our technical support hotline for recommendation on different surface applications. (PHONE: 444 4 595)

Surface and Ambient Temperature
The surface and ambient temperature should be between +5°C and +30°C whilst at application.

Close

Mantotherm Graind Exterior Coating With Silicone

Acrylic emulsion based, textured, grained, long-lasting coating with silicone additive, which is applied and is also given pattern with a roller. The product is also suitable for use on interior walls for decorative purposes.

Mantotherm Silikonlu, Grenli Dış Cephe Kaplaması is used as the finishing coat coating material along with the suitable primer on cement based plaster, exposed concrete, fiber cement board and thermal insulation systems on the exteriors of any building.

Reference Standards

a. Certifications / Standards
TS 7847
b. Ministry of Public Works and Settlement Item No.
Ministry of Public Works and Settlement Item No.: 04.522/R

Application Surfaces
Outdoors Walls;
Cement based plasters (Mantotherm Astar applied)
Exposed concrete (MegaSıva K and MegaSıva İ applied)
Fiber cement panels (Mantotherm Astar applied)
Thermal insulation systems (as finishing coat paint)

Surface Preparation :
• Application surfaces should be sound, clean, dust free, and free from molding oils and other foreign substances. Such materials as mortar and cement residues should be peeled off.
• Mantotherm Astar should be applied to such surfaces, which may have been painted previously or is to be newly painted.

Application Methods :
• Mantotherm Silikonlu, Grenli Dış Cephe Kaplaması should be stirred until it becomes homogenously consistent prior to the application.
• The pelt roller should be thoroughly saturated with the product prior to, and the product should be spread on the entire surface at equal thickness with the roller during the application.
• The patterns should be designed and developed from top to bottom with a coral roller or crystal roller while the product applied is wet. The thickness of the design pattern can be adjusted by adding water; however, it should be noted that the addition of excessive amount of water might cause the design pattern to fade out, impair the coating capability thereof and, depending on the season, cause delays in the drying process of the product.

Application Recommendations :
• In order to avoid any potential differences in shade on the façade, the product of the same batch number should be used on each facade.
• Paper tape should be used and adequate number of application workers should be employed in order to prevent the formation of undesired joint spots in the case of large surface applications.
• In order to avoid any potential differences in shade on the facade, the product of the same batch number should be used on each facade.
• The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing.
• Due care should be taken to ensure that the material is not exposed to direct sunlight in hot weather conditions, and the product should be mixed with cold water.
• The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance.
• Pelt roller may be used to develop different design patterns. The application equipment used should be cleaned with water immediately after the application.
• Refer to our technical support hotline for recommendation on different surface applications. (PHONE: 444 4 595)

Surface and Ambient Temperature
The surface and ambient temperature should be between +5°C and +35°C whilst at application.

Close

Mantotherm Plastic Spiked Euro Dowels

Dowel used for the mechanical assemblage of thermal insulation panels on brick, plaster and concrete surfaces.

Mantotherm Plastic Spiked Euro Dowels are used for the mechanical assemblage of such thermal insulation panels as XPS and EPS in indoors and outdoors spaces of all buildings.

Application Surfaces

  • Mantotherm Platin Thermal Insulation Panel
  • Mantotherm EPS Therrnal Insulation Panel
  • Mantotherm XPS Thermal Insulation Panel

Surface Preparation :
• The application surface should be dry, clean, sound and dust-free, and should have been cleansed of oil, dirt or any materials that may prevent adhesion, and any such materials as mortar and cement residues that impair the surface smoothness should be scraped from the application surface.

Application Methods :

• Minimum 24 hours after the adhesion of the thermal insulating boards, the dowelling should be performed Appropriate and suitable dowels should be selected with due consideration of the insulating material employed and the surface characteristics.
• The drilling diameter should be selected to match the dowel diameter in respect of the dowel bores to be drilled on the panels. • Installation of counterboring apparatus on the drill bit while drilling dowel bores will ensure the drilling of the space for the deployment of the dowel bit as well as drilling the bores. Using counter-boring apparatus will prevent the dowels placed on the panel from causing thickness on the surface, which will also prevent increased consumption of plaster on such account.
• The dowels should be placed into the bores drilled, and the dowel spikes should be pounded completely.
• Once the dowels are placed into the counter-bore gap, the gap to remain around the dowel prior to the primary plaster coat should be filled with the same plaster.
• Six dowels per m2 should be applied on the building surface, 4 of which should be applied on the joints of the panels horizontally and vertically and 2 of which should be applied in the middle of the panels.
• In the case of the panels applied to the edges of the buildings, the number of dowels to be used should be increased with consideration of the wind force; and accordingly, 6 dowels should be used for heights up to 8 meters, 8 dowels should be used for heights between 8 to 20 meters, and 10 dowels should be used for heights in excess of 20 meters.

Application Recommendations :
The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing.
• Due care should be given to prevent the exposure of the material to direct sunlight in hot weather conditions.
• The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance.
• The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours.
• Refer to our technical support hotline for recommendation on different surface applications. 

 

Surface and Ambient Temperature
The surface and ambient temperature should be between +5°C and +30°C whilst at application.

 

 

Close

Mantotherm Plastic Spiked Wide Flange Dowels

Dowel used for the mechanical assemblage of thermal insulation panels on brick, plaster and concrete surfaces.

Mantotherm Plastic Spiked Wide Flange Dowels are used for the mechanical assemblage of such thermal insulation panels as XPS and EPS in indoors and outdoors spaces of all buildings.

Application Surfaces

  • Mantotherm Platin Thermal Insulation Panel
  • Mantotherm EPS Therrnal Insulation Panel
  • Mantotherm XPS Thermal Insulation Panel

 

Surface Preparation :
• The application surface should be dry, clean, sound and dust-free, and should have been cleansed of oil, dirt or any materials that may prevent adhesion, and any such materials as mortar and cement residues that impair the surface smoothness should be scraped from the application surface.

Application Methods :
• Minimum 24 hours after the adhesion of the thermal insulating boards, the dowelling should be performed Appropriate and suitable dowels should be selected with due consideration of the insulating material employed and the surface characteristics.
• The drilling diameter should be selected to match the dowel diameter in respect of the dowel bores to be drilled on the panels. • Installation of counterboring apparatus on the drill bit while drilling dowel bores will ensure the drilling of the space for the deployment of the dowel bit as well as drilling the bores. Using counter-boring apparatus will prevent the dowels placed on the panel from causing thickness on the surface, which will also prevent increased consumption of plaster on such account.
• The dowels should be placed into the bores drilled, and the dowel spikes should be pounded completely.
• Once the dowels are placed into the counter-bore gap, the gap to remain around the dowel prior to the primary plaster coat should be filled with the same plaster.
• Six dowels per m2 should be applied on the building surface, 4 of which should be applied on the joints of the panels horizontally and vertically and 2 of which should be applied in the middle of the panels.
• In the case of the panels applied to the edges of the buildings, the number of dowels to be used should be increased with consideration of the wind force; and accordingly, 6 dowels should be used for heights up to 8 meters, 8 dowels should be used for heights between 8 to 20 meters, and 10 dowels should be used for heights in excess of 20 meters. 

Application Recommendations :
The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing.
• Due care should be given to prevent the exposure of the material to direct sunlight in hot weather conditions.
• The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance.
• The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours.
• Refer to our technical support hotline for recommendation on different surface applications.

Surface and Ambient Temperature
The surface and ambient temperature should be between +5°C and +30°C whilst at application.

 

 

Close

Mantotherm Primer

Highly adhesive, acrylic emulsion based, opaque, white, solvent-free primer with filling.

Mantotherm Astar is used in order to enhance adherence and reduce consumption under siding and paint on cement based, plastered surfaces.

Reference Standards

a. Certifications / Standards
TSE K 208
b. Ministry of Public Works and Settlement Item No.
Ministry of Public Works and Settlement Item No.: 04.503/1

Application Surfaces
Indoors and Outdoors Walls;
Cement based plaster

Surface Preparation :
Application surfaces should be sound, clean, dust free, and free from molding oils and other foreign substances. Such materials as mortar and cement residues should be peeled off.

Application Methods :
• The decorative coating and painting should be commenced minimum 12 hours after the application of Mantotherm Astar.

Application Recommendations :
• Any foreign material should not be added into the product during the application.
• Any extra water should not be added to the mixture.
• The product should not be applied on unsound surfaces. The soundness and the load bearing capacity of old surfaces should be checked prior to adhesion.
• The surface should be preserved from air currents and water contact during and after the application.
• The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing.
• Due care should be given to prevent the exposure of the material to direct sunlight in hot weather conditions.
• The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance.
• The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours.
• Refer to our technical support hotline for recommendation on different surface applications.

Surface and Ambient Temperature
The surface and ambient temperature should be between +5°C and +30°C whilst at application

Close

Mantotherm Rockwool Thermal Insulation Panel

The thermal, noise and fire insulation material, which is developed through the transformation of volcanic rocks by melting at high temperatures.

Mantotherm Taşyünü Isı Yalıtım Levhası is used as heat insulation material for the internal and external walls, terraces, floors and basements of buildings.

  • Application Surfaces
    Outdoors Walls;
    Roughcast applied surfaces Indoors Walls;
    Finishing coat applied surfaces
    Terraces and Roofs

 

Surface Preparation :
• The application surface should be dry, clean, sound and dust-free, and should have been cleansed of oil, dirt or any materials that may prevent adhesion, and any such materials as mortar and cement residues should be scraped from the application surface.
• The old plaster coat, blistering and cracks on the facades should be scraped, be repaired with MegaTamir I or MegaTamir K, whereby a sound surface should be obtained.
• In the case of bevels in excess of 2 cm on the surface; they should be repaired with MegaTamir I or MegaTamir K before insulation application.
• The surface to be insulated should not be moist, and the flooring trowel coating and internal and external wall plasters should have dried.
• There should not be any moisture in progress upward on the surface, the waterproofing should be completed as necessary and should have risen 30 cm above the ground soil.
• The insulation application should be initiated minimum 4 weeks after the application of roughcast.
• The rain gutters, cabling elements and the like on the façade should be placed over the system and be deployed in some 6 to 7 cm distance to the system. 

Application Methods :
• Mantotherm Taşyünü Isı Yalıtım Levhası, the reserve side of should have been applied Mantotherm Yapıştırma Harcı adhesive mortar, should be firmly placed on the sub-basement profile.
• In order for Mantotherm Taşyünü Isı Yalıtım Levhası to thoroughly contact the wall and to ensure the smoothness of the surface, the board should be slipped slightly and adhered to the wall, be gauged and linaged.
• Mantotherm Taşyünü Isı Yalıtım Levhası should be furnished in tusk tenon fashion. The tusk tenon should be continued also in the corner joint spots of the building.
• Any unintentional gaps between any two Mantotherm Taşyünü Isı Yalıtım Levhası should strictly be filled with pieces to be cut from the same material. Due care must be taken to ensure that the adhesive does not overflow at the edges, where boards join, any overflowing adhesive should be cleaned and the board edges should be ensured to be clean.
• The corners of the such gaps on the surface as window gaps and door gaps should be aligned with the board joints, the thermal insulating boards should be placed as a whole on the corners, screw threads should be cut and be sized for the gaps. Hence will be eliminated the risk of cracks on the corners.
• Mechanical fixation on the surface of the thermal insulating boards in addition to chemical adhesion is of utmost importance for long-lasting performance. Minimum 24 hours after the adhesion of the thermal insulating boards, the dowelling should be performed with thermal insulation panel dowels; Mantotherm Isı Yalıtım Levhası Dübelleri. Appropriate and suitable dowels should be selected with due consideration of the insulating material employed and the surface characteristics. 

Application Recommendations :
• The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing.
• Due care should be given to prevent the exposure of the material to direct sunlight in hot weather conditions.
• The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance.
• The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours.
• Refer to our technical support hotline for recommendation on different surface applications.

Surface and Ambient Temperature
The surface and ambient temperature should be between +5°C and +30°C whilst at application.

 

 

Close

Mantotherm Platinum Thermal Insulation Panel

Carbon refractory reinforced expanded polystyrene board with high pressure resistance, used for the heat insulation of walls, columns and girders.

Mantotherm Platin Isı Yalıtım Levhası is used as thermal insulation material for the walls, terraces, floors and basements of buildings.

Application Surfaces
Outdoors Walls;
Roughcast applied surfaces Indoors Walls;
Finishing coat applied surfaces

 

Surface Preparation :
• The application surface should be dry, clean, sound and dust-free, and should have been cleansed of oil, dirt or any materials that may prevent adhesion, and any such materials as mortar and cement residues should be scraped from the application surface.
• The old plaster coat, blistering and cracks on the facades should be scraped, be repaired with MegaTamir I or MegaTamir K, whereby a sound surface should be obtained.
• In the case of bevels in excess of 2 cm on the surface; they should be repaired with MegaTamir I or MegaTamir K before insulation application.
• The surface to be insulated should not be moist, and the flooring trowel coating and internal and external wall plasters should have dried.
• There should not be any moisture in progress upward on the surface, the waterproofing should be completed as necessary and should have risen 30 cm above the ground soil.
• The insulation application should be initiated minimum 4 weeks after the application of roughcast.
• The rain gutters, cabling elements and the like on the façade should be placed over the system and be deployed in some 6 to 7 cm distance to the system. 

Application Methods :
• Mantotherm Platin Isı Yalıtım Levhası, the reserve side of should have been applied Mantotherm Yapıştırma Harcı, should be firmly placed on the sub-basement profile.
• In order for Mantotherm Isı Yalıtım Levhası to thoroughly contact the wall and to ensure the smoothness of the surface, the board should be slipped slightly and adhered to the wall, be gauged and linaged.
• Mantotherm Platin Isı Yalıtım Levhası should be furnished in tusk tenon fashion. The tusk tenon should be continued also in the corner joint spots of the building.
• Any unintentional gaps between any two Mantotherm Platin Isı Yalıtım Levhası should strictly be filled with pieces to be cut from the same material. Due care must be taken to ensure that the adhesive does not overflow at the edges, where boards join, any overflowing adhesive should be cleaned and the board edges should be ensured to be clean.
• The corners of the such gaps on the surface as window gaps and door gaps should be aligned with the board joints, the thermal insulating boards should be placed as a whole on the corners, screw threads should be cut and be sized for the gaps. Hence will be eliminated the risk of cracks on the corners.
• Mechanical fixation on the surface of the thermal insulating boards in addition to chemical adhesion is of utmost importance for long-lasting performance. Minimum 24 hours after the adhesion of the thermal insulating boards, the dowelling should be performed with thermal insulation panel dowels mantotherm Isı Yalıtım Levhası Dübelleri. Appropriate and suitable dowels should be selected with due consideration of the insulating material employed and the surface characteristics.

Application Recommendations :
• The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing.
• Due care should be given to prevent the exposure of the material to direct sunlight in hot weather conditions.
• The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance.
• The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours.
• Refer to our technical support hotline for recommendation on different surface applications.

Surface and Ambient Temperature
The surface and ambient temperature should be between +5°C and +30°C whilst at application.